Материал из IrkutskWiki
Перейти к: навигация, поиск

Learning how to build your own PERSONAL COMPUTER from scratch is usually a very difficult task find out nothing about personal computers. However once you learn how to do it along with understand exactly how to handle it, it actually will become quite enjoyable having the capacity to easily strip down and build up old or new PC's. I would like to take this chance to lay out the basic components of a computer and help you discover ways to build a personal computer from scratch.

PC Components

The most widespread pc components that you will need to have are the mouse, keyboard, hard drive, floppy drive, ram chips, sound and artwork card, power supply, motherboard and check. I'm assuming that you'll know what these components look like. If you are generally unsure about some components just seek out pictures of them on the web and you will spot what they are.

Connection Process

Firstly you have to use the mother board and the mother board increasing plate. Firstly, gently screw your motherboard onto the caretaker board plate while using notches or screws that have been provided with your package or system. Once this is done you will have to insert the CPU (Central Control Unit) into its slot on the motherboard. Sometimes these COMPUTER sockets have levers which you have to gently release to open it up so observe that. Gently slide your CPU into its socket making certain the pins about the backside slide in correctly otherwise it might get damaged. You can right now clip the lever into place and make certain it is risk-free.

Now you must attach the heatsink towards the CPU chip. You might see that the CPU already includes the heatsink/fan attached to it then you definitely can read further. Now you should connect the little cable from your heatsink fan for the corresponding socket on the motherboard to offer it power.

The next step should be to place the ram chips into their respective slots that happen to be long and slim. Once this continues to be done you might mount the motherboard mounting plate onto along side it of the personal computer and screw/slip it in so that it is attached effectively.

The power supply will be the next component to cope with. The power supply area is normally located at the rear of the pc case which is indicated with screw holes which can be unoccupied. Just try along with maneuver it around to suit with the corresponding holes before you screw it within. The power supply carries a main system connection which gets connected to the power slot for the motherboard, a floppy power connector which gets plugged into the floppy drive or a few standard peripheral electrical power connectors (crimson, yellow and black wires) which get connected to your hard devices and cd roms. You will ought to mount the computer drives, cd roms and also floppy drives as well as connect them together with those connectors being sure that the red insert on each electrical power connector is pointed inwards towards the motherboard. I'll explain why below.

Right, now we move onto the 2 ports on your motherboard called the key and secondary IDE Slots. You will notice them while they are rectangular together with brackets around these. these ports are employed to connect the hard drives and cd roms. The cables that get plugged into these two ports are 40 pin IDE cables using have 3 connections on each cable tv. Make sure the longest area of the cable is linked to the IDE plug-ins. You need to connect the primary IDE cable in the motherboard to your hard drive(s) and the secondary IDE port is utilized to connect your DVD Roms in your motherboard. When you put these IDE cables in to the cdroms and hard drives make sure that the red wire strip is side-by-side with the red-colored wire strip from the power connectors that are connected to those people devices. Consult your manual for those who have one to learn how to use the different jumpers to switch between master and salve drives about each port. This will allow you to choose which hard disks are primary and secondary.

Now that the electricity supply is attached to the motherboard plus the various other components you need to plug graphics along with sound card within their slots. Once this is done be sure you connect the front panel connectors to the corresponding LED lights which means that your lights will arrive when the personal computer boots. Failure to do so will result in non function with the system.

Lastly make sure everything is related properly. This includes the actual external mouse, keyboard, monitor cable along with power cables so that the computer will start and function appropriately. If all is done well then it must be okay.read